Aeg Dishwasher Not Turning On

Reset the GFI if needed. Dishwasher door will not close properly or is crooked.

Aeg Dishwasher Common Error Codes

The thermal fuse is a safety device that keeps the dishwasher from overheating and protects the control board.

Aeg dishwasher not turning on. If the outlet the dishwasher plugs into is a GFI outlet make sure it has not tripped. Pull the wires out by the connectors and label them with tape so you know which terminal they fit in. If the delay start is set cancel.

A fuse in the houses wiring system is defective. Dishwasher door will not stay open. If your dishwasher does not light up or is not getting power check where the dishwasher plugs into the wall.

Open the door and then close it again firmly. The thermal fuse is often located underneath the inner door of. When the thermal fuse fails the control panel will not receive power.

If dishwasher is flashing and the programme is still not starting. Door Not Latching Properly. Mains plug is not plugged in.

The cycle is not starting. Dishwasher does not switch on no light on the panel. If the control panel still shows no signs of.

If the dishes are to. The anti-flood system has been triggered. Dishwasher emits clickingticking noise during cycle.

Dishwasher door does not close. Make sure that the appliance door is closed. You spill liquids or place something across the control panel for more than 10 seconds.

If not remove the motor by removing the retention screws. The programme does not start. AEG cooktops have built-in automatic safety switch off.

Make sure that the mains plug is connected to the mains socket. Close the tap then unplug from the mains and contact AEG Service Force. The anti-flood system has been triggered.

Close the tap then unplug from the mains and contact AEG Service Force. A start time has been selected. Unplug the dishwasher and try plugging something else such as a lamp into the socket.

The mains plug is not plugged in. The appliance becomes too hot eg. The appliance deactivates automatically if.

Dishwasher door shifts up during a wash cycle. For dishwasher models with a delay start timer. Before you check the condition of rinse aid make sure the rinse aid chamber is not empty.

Dishwasher door is defective. The programme does not start. Touch one probe to each terminal.

Close the dishwasher door. The door of the dishwasher is not closed properly. Make sure that there is no damaged fuse in the fuse box.

Dishwasher door drops down or opens by itself. The drain pump in the dishwasher runs continuously - even with the appliance switched off. If this works the problem will be with the dishwasher rather than the socket.

Replace the unit with a new one. Be sure it is plugged in. For more information see Dishwasher - Checking Fuse or Dishwasher - Reset Circuit Breaker.

Turn on your multitester to the X1000 setting. You should receive a reading between 2000 and 3000 ohms. Antiflood operated in the baseturn appliance off and then lay it on its BACK and see if water pours outnow stand it up and retry itIf it does the same thing again in a short time you have a blockage or a leak and will have to strip it to find out where from.

If your dishwasher starts up again by itself there is most likely a issue with the control board replace the main control board assembly. Make sure the dishwasher door is closed tightly and is latched correctly. If the dishwasher does not turn on by itself possibly replace either the console keypad or wire harnesses.

When a saucepan boils dry or oil reaches above 300C. When there is a problem with the rinse aid the dishes will not shed water properly. Reset the fuse or circuit breaker in your home that provides power to the dishwasher.

A problem with the rinse aid or its dispensing cap can be one of the reasons why the machine is not drying the dishes properly. The drain pump in the dishwasher runs con- tinuously even with the appliance switched off. Plug in mains plug.

Aeg Dishwasher Common Error Codes